Store

Spindle Lock Nut 3/4 Ton AFCO

The steel spindle nut is designed to be used on a 9" Ford rear end or any 3/4 ton snout using 1-13/16-16 thread. This is a locking nut to keep the main spindle nut from backing off.

part #10150

Steel Wheel Stud 5/8 Inch Diameter Coarse Thread with .812 Inch Knurl AFCO

The steel wheel stud is 3 inches long and 5/8"-11 UNC thread that fits any hub that requires a 5/8 stud and a .812" knurled shoulder. The stud is made from high quality grade 8 pre-stressed aerospace material and is black oxide coated for ultimate durability and corrosion resistance.

part #10152

Bolt GM Caliper Pin AFCO

The steel caliper bolt is designed to replace a GM stock caliper bolt. The caliper bolt is designed to eliminate the need for the stock spacer on the caliper bolt increasing strength and durability. The bolt is 4.4 inches long and is made of high quality steel that is gold zinc coated to improve wear and durability. It is thread with a standard 7/16-20 UNF and uses a 3/8 hex wrench to install.

part #10160

Steel Wheel Stud 5/8 Inch Diameter X 4 Inches Long Coarse Thread with .812 Inch Knurl AFCO

The steel wheel stud is 4 inches long and 5/8"-11 UNC thread that fits any hub that requires a 5/8 stud with a .350 knurled shoulder. The stud is made from high quality grade 8 pre-stressed aerospace material and is black oxide coated for ultimate durability and corrosion resistance. The stud is ideal when you want to run up to a 1" wheel spacer.

part #10164

Spindle Lock Nut Kit 3/4 Ton AFCO

The 6061 aluminum spindle nut kit is designed to be used on an aluminum quick change rear end or a fabricated spindle that uses a 1-13/16-16 thread. The kit comes with a spindle nut, spacer washer, locking washer, and two 10-24 bolts. The nut requires a standard spindle nut shock of 2-3/8" to install.

part #10200

Spindle Lock Nut Kit 3/4 Ton Steel AFCO

The steel spindle nut kit is designed to be used on an aluminum quick change rear end or a fabricated spindle that uses a 1-13/16-16 thread. The kit comes with a spindle nut, spacer washer, locking washer, and two 10-24 bolts. The nut requires a standard spindle nut shock of 2-3/8" to install.

part #10202

Lock Washer GN IMCA Rear Hub AFCO

The steel lock washer is designed to be used on a grand national style rear end to lock the spindle nut in place. It is made of mild steel and coated with a corrosion resistant coating to prevent rust.

part #10205

Lock Nut (RH)-GN IMCA for Rear Hub AFCO

The steel spindle nut is designed to be used on a grand national style rear end to install the rear hub assembly. It is made of mild steel and coated with a corrosion resistant coating to prevent rust.

part #10206

Bearing 3/4 Ton Hub Outer AFCO

The 3/4 ton outer bearing is designed to be used with most wide five style hubs. The tapered roller bearing is made of high quality steel for superior performance and strength.

part #10331

Bearing 3/4 Ton Hub Inner AFCO

The 3/4 ton inner bearing is designed to be used with most wide five style hubs. The tapered roller bearing is made of high quality steel for superior performance and strength.

part #10332

Bearing GN IMCA Rear Hub AFCO

The grand national style bearing is designed to be used with most 9" Ford style rear ends and quick changes with grand national style axle tubes. The tapered roller bearing can be used as a inner or outer bearing and is made of high quality steel for superior performance and strength.

part #10344

Bearing Kit 3/4 Ton Hub AFCO

The bearing kit is designed to be used on an aluminum quick change rear end or a fabricated spindle. The kit comes with inner and outer bearings, hub seal, steel spindle nut, spacer washer, locking washer, and two 10-24 bolts. The nut requires a standard spindle nut shock of 2-3/8" to install.

part #10350

Bearing Kit BEARING/SEAL AFCO

The bearing kit is designed to be used on an aluminum quick change rear end or a fabricated spindle. The kit comes with inner bearing, outer bearing, and hub seal.

part #10351

Bearing Kit 3/4 Ton Hub AFCO

The bearing kit is designed to be used on an aluminum quick change rear end or a fabricated spindle. The kit comes with inner and outer bearings, hub seal, aluminum spindle nut, spacer washer, locking washer, and 2 10-24 bolts. The nut requires a standard spindle nut shock of 2-3/8" to install.

part #10352

Bearing Kit Grand National IMCA Rear Hub AFCO

The grand national style bearing kit is designed to be used with most popular 9" Ford style rear ends and quick changes with grand national style axle tubes. The kit comes with 2 tapered roller bearing can be used as a inner or outer bearing, locking spindle nut, lock washer, and hub seal.

part #10355

Pages