Store

HEADER STREET ROD SMALL BLOCK CHEVY 1.625 INCH 2.50 INCH COLLECTOR. STAINLESS STEEL DYNATECH

This Small Block Chevy Stainless Steel Block Hugger Header is an excellent way to improve the performance and appearance of your street rod. Starting with 100% polished stainless tubing and 3/8 thick last cut flanges, the header looks as good as it fits and performs. Designed specifically to tuck tight to the engine for maximum clearance around steering components, etc. 1.625 primary tubes with a 2.50 collector these come complete with a full color instruction manual and all gaskets and hardware required for assembly. Comes standard with a Full One Year Warranty.

part #730-10010

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

TURNDOWN 4.00 INCH 12.0 INCHES LONG MILD STEEL DYNATECH

4.00 Low Profile Turndown with mandrel bent design for no reduction in exhaust flow. 17 gauge mild steel painted with High-temp black paint. Expanded on one end to slip over 4.00. 11.00 total length.
California Proposition 65 Statement

part #780-00050

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

TURNDOWN 3.00 INCH 10.0 INCHES LONG MILD STEEL DYNATECH

3.00 Low Profile Turndown with mandrel bent design for no reduction in exhaust flow. 17 gauge mild steel painted with High-temp black paint. Expanded on one end to slip over 3.00. 9.75 total length.

part #780-00100

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

TURNDOWN 3.50 INCH 10.0 INCHES LONG MILD STEEL DYNATECH

3.50 Low Profile Turndown with mandrel bent design for no reduction in exhaust flow. 17 gauge mild steel painted with High-temp black paint. Expanded on one end to slip over 3.50. 9.75 total length.

part #780-00200

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

BAND CLAMP 2.50 INCH STEPPED STAINLESS STEEL DYNATECH

Dynatech Stainless Band Clamps offer proven reliability when sealing up any exhaust system. Unlike the typical 1.00 wide clamp that only makes contact with one of the exhaust pipes, this clamp is 3.00 wide and stepped. This allows the clamp to make contact with both exhaust tubes and seal up the slip fit connection. These are used on all of the Dynatech SuperMAXX Exhaust Systems. With excellent sealing capability, they are commonly used with connections near O2 sensors where sealing must be at a premium. Available in 2.5, 2.75, 3.00 and 3.50. Sold individually.
California Proposition 65 Statement

part #789-70250

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

BAND CLAMP 2.75 INCH STEPPED STAINLESS STEEL DYNATECH

Dynatech Stainless Band Clamps offer proven reliability when sealing up any exhaust system. Unlike the typical 1.00 wide clamp that only makes contact with one of the exhaust pipes, this clamp is 3.00 wide and stepped. This allows the clamp to make contact with both exhaust tubes and seal up the slip fit connection. These are used on all of the Dynatech SuperMAXX Exhaust Systems. With excellent sealing capability, they are commonly used with connections near O2 sensors where sealing must be at a premium. Available in 2.5, 2.75, 3.00 and 3.50. Sold individually.

part #789-70275

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

BAND CLAMP 3.00 INCH STEPPED STAINLESS STEEL DYNATECH

Dynatech Stainless Band Clamps offer proven reliability when sealing up any exhaust system. Unlike the typical 1.00 wide clamp that only makes contact with one of the exhaust pipes, this clamp is 3.00 wide and stepped. This allows the clamp to make contact with both exhaust tubes and seal up the slip fit connection. These are used on all of the Dynatech SuperMAXX Exhaust Systems. With excellent sealing capability, they are commonly used with connections near O2 sensors where sealing must be at a premium. Available in 2.5, 2.75, 3.00 and 3.50. Sold individually.
California Proposition 65 Statement

part #789-70300

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

BAND CLAMP 3.50 INCH STEPPED STAINLESS STEEL DYNATECH

Dynatech Stainless Band Clamps offer proven reliability when sealing up any exhaust system. Unlike the typical 1.00 wide clamp that only makes contact with one of the exhaust pipes, this clamp is 3.00 wide and stepped. This allows the clamp to make contact with both exhaust tubes and seal up the slip fit connection. These are used on all of the Dynatech SuperMAXX Exhaust Systems. With excellent sealing capability, they are commonly used with connections near O2 sensors where sealing must be at a premium. Available in 2.5, 2.75, 3.00 and 3.50. Sold individually.

part #789-70350

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

GASKET STANDARD PORT SET DYNATECH

Dynatech Fiber Race Gaskets are the premium gaskets demanded by many enthusiasts and racers alike. Specifically designed to fit a wide variety of ports and applications, these gaskets are sure to provide many years of service. Sold in pairs.

part #794-00001

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

U TAB KIT INCLUDES U TABS AND HARDWARE STAINLESS STEEL DYNATECH

The Dynatech U Tab Kit is an excellent way to connect exhaust components on racing applications. Lightweight and easy to install, it is a must-have for any racer. The single bolt allows for easy disassembly when needing to remove a component. This kit comes with two stainless steel U Tabs, one bolt and one locking nut.
California Proposition 65 Statement

part #794-00310

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

U TAB KIT INCLUDES U TABS AND HARDWARE STAINLESS STEEL DYNATECH

The Dynatech U Tab Kit is an excellent way to connect exhaust components on racing applications. Lightweight and easy to install, it is a must-have for any racer. The single bolt allows for easy disassembly when needing to remove a component. This kit comes with four stainless steel U Tabs, two bolts and two locking nuts.
California Proposition 65 Statement

part #794-00313

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

U TAB KIT DYNATECH

Dynatech Fiber Race Gaskets are the premium gaskets demanded by many enthusiasts and racers alike. Specifically designed to fit a wide variety of ports and applications, these gaskets are sure to provide many years of service. Sold in pairs.
California Proposition 65 Statement

part #794-00315

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

U TAB KIT INCLUDES U TABS AND HARDWARE STAINLESS STEEL DYNATECH

The Dynatech U Tab Kit is an excellent way to connect exhaust components on racing applications. Lightweight and easy to install, it is a must-have for any racer. The single bolt allows for easy disassembly when needing to remove a component. This kit comes with eight stainless steel U Tabs, four bolts and four locking nuts.
California Proposition 65 Statement

part #794-00320

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

GASKET LS-1 ROUND PORT SET DYNATECH

Dynatech Fiber Race Gaskets are the premium gaskets demanded by many enthusiasts and racers alike. Specifically designed to fit a wide variety of ports and applications, these gaskets are sure to provide many years of service. Sold in pairs.

part #794-20001

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

J BEND 1.625 INCH O.D. 12.00 INCH LEG ON ONE SIDE 6.00 INCH LEG ON THE OTHER MILD STEEL DYNATECH

Dynatech 1-5/8 J-Bends offer a great way to build your own headers or exhaust system for that custom build. Mild steel construction with a 6.00 straight leg on one side and a 12 straight leg on the other. The 180 degree bend is mandrel bent for superior exhaust flow throughout the bend. A 1.6D bend radius allows for a tight fit that doesnt restrict flow. Outside to outside = 6.875 , Inside to Inside = 3.625 and Center to Center = 5.200".

part #794-60202

These products are intended for racing and off-road applications. Not legal for sale or use in the state of Ca

Pages